HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-1-160T Hot Press, Single daylight opening. Suitable for pressing High Temperature materials.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) 100 mm diameter Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 25" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 100 mm diameter, rack & Pinion guide system for parallel closing of the platens. -- 160 Ton total pressure, 46 PSI specific pressure over the entire platen area; 7.5 KW (10 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 92 kW Electric Heater with 1.5 kW (2 HP) Hot Oil circulation pump; approximately 180° C (356° F) maximum operating temperature. -- Loading from (3) sides, heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 20,900Lbs).

HYDREX HPX510-5 Hot Press 120 Tons, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (6) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (6) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 KW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs.

HYDREX HPX510-5 Hot Press 160 Tons, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 KW heating power. Approx. 7.5 KW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Available: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

This Pneumatic Vertical Clamping System features upper and lower 12" wide and up to 126" long steel platens for face gluing a variety of solid wood components. With it's modular design with each section having its own pressure control and 40" opening. -- 12" Deep x 42" wide clamping cap. -- Air operated assembly, for face gluing of engineered stiles & rails, kickers, headers, and many other solid wood applications. -- Single lever valve operation with dial regulator pressure controls for quick & accurate clamping pressure. -- Up to 30 Ton max. clamping pressure @ 120 PSI.

This Pneumatic Vertical Clamping System features upper and lower 12" wide and up to 42" long steel platens for face gluing a variety of solid wood components. With it's modular design with each section having its own pressure control and 40" opening, 13" daylight. -- 12" Deep x 42" long clamping cap. -- Air operated assembly, for face gluing of engineered stiles & rails, kickers, headers, and many other solid wood applications. -- Single lever valve operation with dial regulator pressure controls for quick & accurate clamping pressure. -- Up to 30 Ton max. clamping pressure @ 120 PSI.

JLT 78H-16W-42L Mini Air Pod PressThis Pneumatic Vertical Clamping System features upper and lower 16" wide and up to 42" long steel platens for face gluing a variety of solid wood components. With its modular design with each section having its own pressure control and 40" opening, Specifications: -- 16" Deep x 42" long clamping capacity. -- Air-operated assembly, for face gluing of engineered stiles & rails, kickers, headers, and many other solid wood applications. -- Single lever valve operation with dial regulator pressure controls for quick & accurate clamping pressure. -- Up to 30 Ton max. clamping pressure @ 120 PSI.

JLT 78H-16W-84L-40H-M4 Pneumatic Pod Press w/adjustable Opening.Specifications: -- Pneumatic Vertical Clamping System features upper and lower 16" wide and up to 84" long steel platens for face gluing a variety of solid wood components. -- Powered by a total of (18) 20 square inch diaphragm cylinders. -- With it's modular design each section has its own pressure control and 40" opening. -- 16" Wide x 84" Long x 40" High with fixed clamping opening with 1-1/2" adjustable increments. -- Air-operated assembly, for face gluing of engineered stiles & rails, kickers, headers, and many other solid wood applications. -- Single lever valve operation with dial regulator pressure controls for quick & accurate clamping pressure. -- Up to 30 Ton max. clamping pressure @ 120 PSI.

JOOS JUNIOR III Hot Press 98.4" x 49.2" Platen size is perfect for up to 4' x 8' panels.Specifications: -- 4-3/4" Maximum opening/stroke, Bottom platen slides sideways in and out for layup & loading. -- 80 Tons max. pressure, specific pressure 39 PSI, pneumatic 14-airbag pressure system requires 85 PSI compressed air hookup only; Equipped with: -- Micro-chronometer pressing cycle timer. -- Separate temperature adjustment for top & bottom platens, electrically heated for up to 90° C (190° F) operating temperature. -- The press has a "safety" pull rope on all (4) sides.

NEWMAN HP-688 Hydraulic Cold Press; 6-Sections (top platens) each 24" x 84" each; 190 tons per platen, for a total tonnage of 1,140 tonsSpecifications: -- Center posts between second and third platens, and between fourth and fifth platens, creating three overall areas of 49" x 84". -- Max. fixed opening 52" with 12" cylinder stroke, each platen section has (2) 10" bore with 5" dia. ram cylinders; -- 26-1/2" Working height (bed-to-floor), dual spring loaded rows of rollers in lower platen for easy loading & removal of panels. -- Approx. 3,000 PSI pressure/head (150 PSI specific pressure), side-mounted self-contained hydraulic system w/tank, 10 HP continuous operating pressure compensating pump. -- Manual pressure control and directional control and gauge for each platen. -- Depressable rollers in the bottom platen for easy loading and unloading.

-At Auction - CNC Bore, Rout & Cam Inserter,All Axes CNC-Controlled

ORMA NPC/DIGIT 31/13 Hydraulic Hot Press (Oil Heated Platens)Main Features: -- Press platen dimension 3100 x 1300 mm (122" X 51") -- Max. total thrust 160 T (metric) - 352,000 Lbs -- Pressure over 80% of platen 5.0 Kg/cm² (71 PSI) -- Pressing cylinders (8) Ø 85 mm with 450 mm (17-3/4") stroke -- Movable platen lower (upstroke design) -- Opening 450 mm (17-3/4") -- Loading side 3100 mm (122") side Structure: -- Press structure in steel beams welded together on a precision jigs; locating surfaces are CNC tool machined -- The lower mobile platen and the upper fix platen structure are in beams welded on a precision jigs. -- Double rack and pinion system (both length and crosswise) to grant a perfect platens’ parallelism when the mobile one is moving up/downward. -- Movable platen locking system in order to work safely during the maintenance operations Hydraulic System: -- Hydraulic power unit (HAWE) composed by a double stage pump and a motor which are submersed in the hydraulic oil for a less noisiness and a better lubrication of the rotating parts. Closing stage (high delivery at low pressure) and thrusting stage (low delivery at high pressure). Both pumps are protected by a pressure relief valve. -- This system allows the use of lower consumption motors increasing the efficiency of the plant. -- Unit fitted with control and safety valves located in a group over the hydraulic oil tank lid -- The circuit comes filled with the necessary hydraulic oil to run the press. -- Rams are in steel suitable for hydraulic applications and are designed to work at the max pressure adjustable on the press. Electric System: -- Main control board (SIEMENS components) including: -- Dual timed press closing push buttons; press opening push button. -- Main on/off switch. -- Tension light. -- Emergency push button Operator control, touch screen panel, with: -- 7” Digital display, SIEMENS "KTP700 BASIC COLOR" equipped with ETHERNET NET for remote assistance connection (it requires access to your Internet + Service pack) to set and control the following functions: -- Setting and display of the working pressure -- Setting and display of the working temperature (presses with electric heater) -- Setting and display of the pressing time for automatic opening -- Setting of the heating plant automatic switching on (presses with electric heater). Possibility of all week days settingpossibility to automatically set the partial use the power consumption of the boiler when it reaches the set temperature (for presses

ORMA NPC DIGIT 36/16, ...5' x 12' Electric Hot Press For Solid Surface & Panel Dye SublimationSide Opening Press designed to work with Dye Sublimation materials to print into Solid Surfaces, as well as Panels that can receive Dye Sub Inks. The Press has (6) Pressing Cylinders, 70 mm dia. (2-3/4"), and an opening of 400 mm (15-3/4").Electric Heated Platens: -- ELKOM Germany 3,700 x 1,600 x 24 mm ( 145-1/2" x 63" x 1") + 19 mm (3/4") Monolux + 19 mm (3/4") V100. -- Each platen requires 31 kW, Voltage 440 V / 3 Ph. / 50/60 Hz. -- Max. working temperature is 180°C (356° F). -- Gold anodized surface; massive, solid top of 12 mm (1/2") thick sheet, flat platen surface without any screw; Heat-up time from room temperature to 160°C (320° F): ca. (45) Minutes.Operator & Machine Controls: -- Integrated CNC operator panel on the front right beam with 6” KTP600 BASIC SIEMENS color Touch-Screen control. -- Complete with individual programmable electronic control (PLC), central unit CPU, and expansion possibility of inputs & outputs. Hardware by SIEMENS, software by ORMAMACCHINE.Manual controls for : -- Push buttons for Press closing and manual Press opening. -- Emergency lamp and emergency push button. -- General on/off switch. -- Power signal lamp.Digital controls for : -- Automatic adjustment of the requested pressure in bar (with automatic recovery of pressuredecrease) obtained by setting the working pieces area and the desired specific pressure. -- Setting & digital display of working temperature on platens. -- Setting & digital display of pressing time for automatic opening. -- Heating platens on/off. -- Automatic switching on of the platens with the possibility to set every day of the week. -- Possibility to store a max. of (20) working programs (temperature, specific pressure, pressing time, and panel dimensions).Special Features: SILICONE MEMBRANE fitted to the upper platen and fixed all around the Press upper structure by means of fast clamping/unclamping units, helps to balance possible uneven profiles and to protect the Press platens from ink transmission.

QUICK MODEL L-HLPP-1-36-43-6 SINGLE SIDED HYDRAULIC LAMINATING PRESS FOR POSTS AND BEAMS: -- Number of working sections: 1 -- Maximum working length: 36'. The 36' length achieved by manufacturing the machines in two 18' long pieces; the two 18' pieces are then joined together, resulting in 36' total working length. -- Maximum working width: 43" -- Maximum working thickness: 6"Main Laminating Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 80mm dia. x 80mm strokeHolddown Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 40mm dia. x 150mm strokeSide Lift Cylinders: -- Number of cylinders: (2) per section = (4) -- Size of cylinders: 63mm dia.Hydraulics: -- Hydraulic pump drive motor: 7-1/2 HP -- Maximum pressure: 140kg/cm2 -- Maximum Holddown Cylinder Pressure: 50kg/cm2 -- Maximum Side Lift Cylinder Pressure: 50kg/cm2 -- NOTE: Shipped without hydraulic oil

QUICK L-HLPP-2-20-43-8-12 ...2-Sided Hydraulic Laminating Press: -- Number of working sections: (2) -- Working width, section #1: 6" and 8" -- Working width, section #2: 8", 10” and 12" -- Maximum working length: 6,200mm (20.3') -- Maximum working height: 1,100mm (43.3") -- Pressure at the glue line: Up to 175 PSIMain Laminating Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 100 mm dia. x 80 mm strokeHolddown Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 40 mm dia. x 150 mm strokeLift Cylinders: -- Number of cylinders: (2) on each side = (4) -- Size of cylinders: 63 mm dia.Hydraulic Pump: -- Drive motor: 10 HP -- Maximum pressure: 140 kG/cm² -- Maximum Holddown Cylinder Pressure: 50 kG/cm² -- Maximum Side Lift Cylinder Pressure: 50 kG/cm² -- Shipped without hydraulic oil in the oil tank

FIXED DAYLIGHT OPENING AIR POD PRESSThis Pod Press can produce a maximum 50 PSI platen pressure over the entire surface at 100 PSI supply air pressure. Press has a fixed vertical daylight opening of 44". The (18) 12.8" max. diameter air pods have 5.9" stroke.Material conveyance is via automatically extending and retracting (via pneumatic cylinders) non-powered roller tracks. A cycle timer provides visual and audible signals at the end of each cycle if desired, and also automatically releases platen air pressure at the end of each cycle, if desired.Specifications: -- Maximum platen pressure: 50 PSI at 100 PSI supply pressure. -- Lower platen dimensions: 4' x 8' -- End-loading or Side-loading: End-loading -- Number of upper platens: 1 -- Upper platen(s) dimensions: 4' x 8' -- Vertical opening: Fixed at 44" -- Lower platen Non-powered roller tracks. -- (18) 12.8" diameter, 5.9" stroke air pods. -- Number of air pressure zones: 1Lead Time: Approximately (12) weeks from time of order.Actual Model: N-P50-04-08-EL-1PL-F-44-R-1ZNOTE: Please let us know of any "Special or Specific" safety equipment requirements that you may have prior to order

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side. -- 50 PSI Platen pressure over the entire surface area with 93 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.Actual Model is a N-P50-05-12-SL-1PL-M-40-R-1Z.• Maximum platen pressure: 50 PSI at 93 PSI supply pressure• Lower platen dimensions: 5' x 12'• Side-loading design• Number of upper platens: 1• Upper platen dimensions: 5' x 12'• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 36• Number of air pressure zones: 1 (5' x 12' pressing)Optional powered roller tracks are available. -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side (also available as end loading). -- 50 PSI Platen pressure over the entire surface area with 90 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- (2) Pressure air pressure zones: 5' x 12' and 4' x 8'. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of idle conveyor roller tracks by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.This machine will include -Leveling bolts, safety guards for Motorized Vertical Adjustment system, upgrading electrical system such that the emergency stop buttons will stop all machine functions, and 2-hand safety feature for Cycle Start function.

QUICK MACHINERY N-P80-03-08-EL-1PL-M-40-R-1ZN-P80-03-08-EL-1PL-M-40-R-1Z Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface. -- Specifications: -- Platen pressing area size: 38" x 98” with end loading on 37" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 1" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 38" X 98". -- Optional: powered roller tracks for $4,875.00 . Specifications:QUICK Laminating Pod PressN-P80-03-08-EL-1PL-M-40-R-1Z• Maximum platen pressure: 81 psi at 90 psi supply pressure• Lower platen dimensions: 3' x 8' (38" x 98")• End-loading or Side-loading: End-loading• Number of upper platens: 1• Upper platen(s) dimensions: 3' x 8' (38" x 98")• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, Non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 24• Number of air pressure zones: 1 -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 49" x 97" with end loading on 49" side. -- 80 PSI Platen pressure over the entire surface area with 102 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (28) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 49" X 97" . -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-04-08-EL-1PL-M-40-R-1Z